Electrostatics problems become more manageable when you separate force, field, potential, and energy before choosing an equation. This revision guide gives you a repeatable method for Coulomb’s law questions, electric field strength problems, superposition, uniform fields, and capacitors, with worked examples, sign checks, and a practical review schedule for physics exam preparation.
Overview
Electrostatics describes charges at rest and the interactions they produce. Most exam questions use the same small group of ideas, but errors occur when similar quantities are treated as interchangeable. Begin by identifying what the question asks for and whether the answer is a scalar or a vector.
| Quantity | Meaning | Equation | Type and unit |
|---|---|---|---|
| Electric force, F | Push or pull on a particular charge | F = kq1q2/r2 | Vector; newton (N) |
| Electric field strength, E | Force per unit positive charge at a point | E = F/q or E = kQ/r2 | Vector; N C−1 or V m−1 |
| Electric potential, V | Potential energy per unit charge | V = W/q or V = kQ/r | Scalar; volt (V) |
| Electric potential energy, U | Energy associated with a charge’s position | U = qV or U = kqQ/r | Scalar; joule (J) |
Here, k is the Coulomb constant, approximately 8.99 × 109 N m2 C−2 in vacuum or air. Use the value supplied by your course or examination paper when one is provided. Convert centimetres or millimetres to metres and microcoulombs or nanocoulombs to coulombs before substituting.
A useful distinction is that electric field and force have direction, while electric potential and potential energy do not. A positive source charge produces a field directed away from it; a negative source charge produces a field directed toward it. The force on a positive test charge follows the field, while the force on a negative test charge is opposite to the field.
What to track
1. Charge, distance, and units
For every electrostatics question, list the known values with signs and units. Mark the separation between charge centres, not the distance from an edge unless the diagram explicitly defines it that way. Because Coulomb’s law contains r2, doubling the separation reduces the force or point-charge field strength to one quarter. This inverse-square relationship is one of the quickest reasonableness checks.
2. Direction before calculation
Draw a simple charge-and-direction diagram before entering numbers. Label each charge, draw the force or field contribution from each source, and decide whether the arrows point toward or away from the source. For a force question, focus on the charge experiencing the force. For a field question, imagine a small positive test charge at the point of interest.
- Like charges repel.
- Unlike charges attract.
- Fields point away from positive charges and toward negative charges.
- Forces and fields must be added as vectors, not merely as positive magnitudes.
- Potential contributions are added algebraically, including their signs.
3. The problem type
Track which model applies. Use Coulomb’s law for the force between two point charges. Use E = kQ/r2 for the field from a point source. Use superposition when several charges contribute at the same location. Between large, oppositely charged parallel plates, use the uniform-field relationship E = V/d, where d is plate separation. For a capacitor, monitor charge, potential difference, capacitance, and stored energy using Q = CV and U = ½CV2 = ½QV.
Worked problem: Coulomb’s law
Question: Two charges, +3.0 μC and −2.0 μC, are separated by 0.40 m. Find the magnitude and direction of the force on the −2.0 μC charge.
- Convert the charges: 3.0 μC = 3.0 × 10−6 C and −2.0 μC = −2.0 × 10−6 C.
- Use the magnitude form of Coulomb’s law: F = k|q1q2|/r2.
- Substitute: F = (8.99 × 109)(3.0 × 10−6)(2.0 × 10−6)/(0.40)2 ≈ 0.337 N.
- The charges have opposite signs, so the force is attractive. The force on the negative charge points toward the positive charge.
The final answer should therefore be about 0.34 N toward the positive charge. The sign of the product identified attraction; it was not a substitute for stating the physical direction.
Worked problem: superposition of electric fields
Suppose a point lies midway between two equal positive charges. The field from the left charge points right, while the field from the right charge points left. The magnitudes are equal because the distances and source charges are equal, so the resultant field is zero. This does not mean each field is absent; it means the vector contributions cancel.
If one source is negative instead, both field arrows at the midpoint point in the same direction: away from the positive charge and toward the negative charge. Calculate each magnitude, choose a positive direction, assign signs to the components, and add them. For a two-dimensional arrangement, resolve each field into horizontal and vertical components before combining them. A vector-components refresher can help when the diagram is not one-dimensional: Physics Vectors Made Simple.
Worked problem: uniform field and capacitor
A potential difference of 600 V is applied across parallel plates separated by 0.030 m. Ignoring edge effects, the uniform field magnitude is
E = V/d = 600/0.030 = 2.0 × 104 V m−1.
The field direction is from the higher-potential plate toward the lower-potential plate. If a positive charge is released between the plates, its electric force follows this direction. A negative charge experiences a force in the opposite direction. Do not confuse electric field direction with the motion direction if the particle is initially moving or if another force acts on it.
For capacitor questions, first identify which variables are fixed. If capacitance is 4.0 μF and the potential difference is 12 V, then Q = CV = (4.0 × 10−6)(12) = 4.8 × 10−5 C. The stored energy is U = ½CV2 = 2.88 × 10−4 J. If the capacitor is disconnected before a change, charge may remain fixed; if it stays connected to a voltage source, potential difference may remain fixed. Read that condition carefully before predicting how energy changes.
Cadence and checkpoints
Use a short review cycle rather than waiting until the night before an exam. On the first pass, learn the definitions and build the comparison table from memory. On the next session, solve one direct Coulomb’s law question, one field-direction question, and one potential or capacitor question without looking at worked steps.
At a weekly checkpoint, complete a mixed set that includes different representations: a written scenario, a charge diagram, a graph, and a numerical calculation. Record recurring errors in a small tracker with four columns: mistake, cause, correct rule, and new example. Useful categories include unit conversion, vector direction, sign handling, choosing r versus r2, and confusing potential with field.
Before a test, practise under the expected time conditions and review the equations permitted by your course. For AP Physics, GCSE, A-Level, or introductory college work, notation and the required level of explanation can differ, so use the equation sheet and command words associated with your syllabus. For broader exam preparation, connect electrostatics to circuit work through this Ohm’s law and circuit problems guide.
How to interpret changes
When an answer differs from your expectation, do not immediately redo every line. Diagnose the pattern. An answer that is 100 times too large often points to centimetres being used as metres or microcoulombs being used as coulombs. A direction opposite to the mark scheme usually indicates that the test-charge sign or attraction-versus-repulsion rule was reversed. A nonzero result where symmetry suggests zero usually means one contribution was omitted or the vector directions were added as magnitudes.
Use units as an active check. Coulomb’s law should produce newtons, E should produce N C−1 or V m−1, potential should produce volts, and energy should produce joules. Also check limiting behaviour: field strength should fall as distance increases, the potential from a positive point charge is positive relative to infinity, and the potential from a negative point charge is negative under that reference convention.
For written solutions, preserve the chain of reasoning: state the model, write the equation, substitute with units, calculate, then give magnitude and direction. This makes partial reasoning visible and helps you locate the first incorrect assumption. If the diagram involves angled charges or several axes, review vector components before attempting the arithmetic.
When to revisit
Revisit this guide monthly during a long course, at the start of a new electricity unit, and before each major assessment. Return sooner when your class introduces a new convention, such as a different reference for potential, a required capacitor energy equation, or a syllabus-specific treatment of fields and practical investigations. The fundamental relationships remain useful, but your course may require particular terminology, diagrams, significant figures, or assumptions.
Use this action list at each checkpoint:
- Write the four key quantities—force, field, potential, and energy—and explain the difference between each pair.
- Convert every charge and distance into SI units before calculating.
- Draw arrows for each force or field contribution and identify the resultant direction.
- Solve one Coulomb’s law, one superposition, one uniform-field, and one capacitor problem.
- Check units, signs, powers of ten, and whether the result changes sensibly with distance.
- Update your error tracker and create a fresh question targeting the mistake you made most often.
Once these steps become routine, electrostatics questions stop being a collection of unrelated formulas. They become a sequence of decisions: identify the quantity, draw the directions, select the model, calculate carefully, and test whether the result makes physical sense.